COB LED Strip 24V 8W/m CRI>90 2700K

LED Damp-Proof Lights for Cellars, Garages and Workshops

LED damp-proof lights are built for rooms where dust, moisture or splash water occur. Their sealed housing with gasket achieves IP65 protection and withstands cleaning with a water jet. Typical locations are cellars, garages, underground car parks, workshops, warehouses and agricultural buildings.

Compared with old fluorescent battens, the LED models save considerable energy and need no tube changes. Length and luminous flux are the main selection criteria: smaller models suffice for cellars, while longer high-output versions make sense in halls. Many luminaires can be linked into continuous light bands.

LED Floodlights for Yards, Facades and Sports Grounds

LED floodlights bring light to large outdoor areas – from the yard and facade to the sports ground. Our range extends from compact 10-watt fittings for the front door to powerful 1.500-watt models for storage yards and sports facilities. All floodlights are weatherproof to IP65 or IP66 and withstand rain, snow and frost.

Some models are available with an infrared motion sensor so the light switches on only when needed, saving energy. Besides wattage, the beam angle matters when choosing: narrow angles reach far, wide angles cover large areas at short distances. We are happy to help determine the right output for your area.

LED Garden Lighting for Outdoor Areas

LED garden lighting stages paths, plants and water features after dark. This category includes inground spotlights for setting into terraces, driveways or lawns as well as underwater lights for ponds, pools and fountains. All fittings are made of stainless steel and protected to IP67 or IP68 depending on the location.

Most models run on 24 volt low-voltage technology, which makes operation outdoors and near water safe. As a planning rule: a few deliberately placed points of light usually work better than uniform continuous lighting. Matching drivers and cable connectors are available in our accessories category.

LED High Bay Lighting for Industry and Commerce

LED high bay lighting has to light large rooms with high ceilings reliably while operating economically. This category includes UFO high bay lights, linear high bay luminaires and canopy fittings for different ceiling heights and uses. Ceiling height, floor area and the type of work are decisive: in warehouses even base brightness matters most, at assembly workstations a low glare rating too.

The beam angle must match the height – narrower for high ceilings, wider for low ones. Compared with old mercury vapour or fluorescent installations, LED high bays often save more than half the energy costs. We are happy to support the design of your hall with a recommendation on quantity and layout.

LED Panels for Office, Practice and Retail

LED panels create a large, evenly lit surface instead of individual bright points. This makes them the standard solution for offices, medical practices, schools and meeting rooms where calm, low-glare light is wanted. We stock backlit panels, in which the LEDs sit behind the diffuser, and edgelit panels with side-fed light and an especially slim design.

The common sizes 60x60, 62x62, 120x30 and 120x60 centimetres are available to suit standard ceiling grids. For ceilings without a grid we offer surface mounting frames that allow direct installation. Watch the UGR value where screen work takes place – the lower, the more comfortable.

LED Track System for Retail and Commerce

An LED track system is the most flexible way to light sales areas. The luminaires are fitted onto the 3-phase busbar via an adapter and can be moved, added to or replaced at any time – with no electrical work at the ceiling. Using the three phases L1, L2 and L3 you switch several lighting groups separately, for example general light and shop window.

This category contains spotlights, linear luminaires, slim panels, food lighting and emergency fittings for the same track. Our adapters fit the common European systems such as Stucchi, Global, Staff, Unipro, Eutrac and Ivela as well as the EU universal standard. If your store layout changes, simply move the luminaires.

LED Street Lighting for Paths, Squares and Residential Areas

LED street lighting replaces old sodium and mercury vapour fittings while considerably reducing energy consumption. This category includes street lights for carriageways, post top luminaires for parks and residential areas, and lanterns in a classic style. All luminaires are protected to IP66 against dust and water jets and built for year-round outdoor use.

Many models allow power and colour temperature to be set by switch, so one fitting serves different situations. In residential areas warm light at 3000 K or below makes sense, as it disturbs residents and insects less. The adapters usually fit poles with 60 and 76 millimetre diameters.

LED Strips for Furniture, Display Cases and Light Lines

LED strips are flexible light bands that can be stuck to almost any surface. Use them to light display cases, shelves, furniture fronts, alcoves and ceiling edges – anywhere a normal luminaire would be too large. We stock two technologies: classic SMD strips with individual visible light points and COB strips that create a continuous, dot-free line of light.

For voltage you can choose between 24 volt low voltage, which needs a driver, and 230 volt strips run directly from the mains. Watch the power per metre: it determines both brightness and the size of driver required. Matching drivers, profiles and connectors are in our accessories category.

LED Accessories for Installation and Operation

A finished lighting project involves more than the luminaire itself. This category contains drivers for LED strips and fittings, motion sensors for retrofitting, brackets and pole adapters as well as cable and plug connectors. Drivers in particular deserve a careful look: the output must match the connected load and should offer around 20 percent headroom so the unit does not permanently run at its limit.

Motion sensors reduce energy costs where light is only needed occasionally – in corridors, stairwells and outdoor areas. Brackets and adapters ensure floodlights and street luminaires sit securely in the intended place. If you are unsure which accessory suits your fitting, just ask us.

24V COB LED strip 5m 320 LEDs/m 2200/2700/3000/4000/6000K CRI>90 IP20 2700K

Item number: COB24V5M2-2

Category: 24V LED Stripes

54,90 €

including 19% VAT., plus shipping

From	Price per unit
3	49,90 €
10	43,90 €
20	38,90 €

Available

Shipping time: 1 - 2 workdays

Description

COB LED Strip 24 V – 2700 K warm white, 8 W/m, CRI > 90

320 LEDs/m · dot-free line of light · 720 lm/m · IP20 · 5 m reel · Sanan LEDs

320 LEDs/m8 W/m720 lm/m2700 KCRI > 9024 VIP205 m

This COB LED strip delivers a continuous band of light instead of a string of dots. That is made possible by 320 very closely spaced LEDs per metre, covered together by a silicone layer. The difference is immediately obvious with indirect lighting: no stripes on the wall, no dot pattern, just a calm, even line.

Key benefits at a glance

No light dots 320 LEDs per metre create a continuous, even line.	Excellent colours CRI > 90 renders wood, fabrics and food true to life.
Cuttable every 5 cm Adapts to any length without wasting offcuts.	Safe 24 volts Low-voltage technology for furniture, cases and reachable areas.
Easy to install Strong adhesive tape on the back, no tools required.	Long service life 50,000 hours with LED chips by Sanan.

Features in detail

COB technology with 320 LEDs per metre for dot-free light
Colour rendering CRI > 90 Ra for natural colours
170° beam angle for wide, soft light distribution
Cuttable every 50 mm at the marked points
Double-sided adhesive tape on the back, 15 cm lead at both ends
Only 8 mm wide and 2.3 mm high – fits narrow profiles and joints
Sanan LED chips for consistent colour temperature across the whole reel

What does COB mean – and why are there no dots?

COB means chip on board and describes how the LEDs sit on the circuit board. Instead of individually housed diodes spaced one to two centimetres apart, 320 very small chips per metre are applied directly and encapsulated together. For you that means no visible light points, no striping on the wall and a far more premium impression where the strip is visible.

CRI > 90: colours that are true

CRI > 90 means particularly true-to-life colour rendering. Simple LED strips with CRI 80 make reds in particular look pale; above 90 the colour spectrum stays complete. You notice it immediately when the strip shines on wood, textiles or food. For display cases, kitchen worktops, retail fittings and living spaces this is the tangible difference in quality.

Colour temperature 2700 K – warm white

2700 kelvin matches the light of a classic incandescent bulb – warm, soft and homely. This is the typical choice for living rooms, bedrooms, hotel rooms and hospitality. With indirect lighting it creates a comfortable base mood that invites you to linger.

High-quality LED chips by Sanan

Fitted are LED chips by Sanan, one of the world's leading manufacturers. The listed company from Xiamen produces several hundred billion LED chips per year and makes everything itself, from wafer to finished chip. With a COB strip carrying 1,600 LEDs across five metres this consistency is decisive: even small variations would show as a colour gradient in the band of light. With Sanan chips the colour temperature stays constant across the whole reel.

Choosing the right driver

You need a 24 volt driver for operation. The right size matters: the strip draws 8 watts per metre, so a complete 5 metre reel needs 40 watts. The driver should not have to supply more than about 80 percent of its rated output continuously – for one reel that means at least 50 watts. If you plan to extend later, factor in the headroom straight away. We stock the matching drivers in accessories.

Installation, cutting and routing

The strip is attached using the adhesive tape on its back. The surface should be smooth, clean and grease-free for the bond to last. You can shorten it every 50 millimetres at the printed markings, where the solder pads for connection sit. Do not crease sharply – a bending diameter of at least 1 cm protects the conductor tracks. Also run a maximum of 5 metres from one supply. There is a simple physical reason: the narrow conductor tracks have a low resistance, but it adds up over distance. At the end of an overly long run less voltage arrives, and the strip glows noticeably weaker there. So feed longer light lines in parallel sections – each reel gets its own supply from the driver, keeping brightness consistent throughout.

Technical data

Type	COB (chip on board), continuous line of light
LED density	320 LEDs per metre
LED chips	Sanan SMD
Power	8 W per metre (40 W per 5 m reel)
Luminous flux	approx. 720 lm per metre
Efficacy	> 90 lm/W
Colour temperature	2700 K (warm white)
Colour rendering	CRI > 90 Ra
Beam angle	170°
Voltage	DC 24 V (driver required)
Protection rating	IP20 (dry indoor areas only)
Dimensions	5,000 × 8 × 2.3 mm
Reel length	5 m per reel
Cuttable every	50 mm
Board	double-sided PCB, electrolytic copper
Fixing	double-sided adhesive tape on the back
Connection	15 cm lead at both ends
Min. bending diameter	10 mm
Service life	50,000 h
Ambient temperature	−20 °C to +40 °C
Storage temperature	−20 °C to +45 °C
Certification	CE, RoHS
Energy efficiency class	F (EU scale A–G, EU 2019/2015)

Applications

The strip is used wherever a clean line of light is wanted: under wall units, in display cases and shelves, behind furniture as indirect light, in ceiling coves, along stair edges and handrails as well as in shop fittings and counters. At 8 millimetres wide it fits most aluminium profiles. Please note the IP20 rating – the strip is suitable exclusively for dry indoor areas.

Scope of delivery

1× COB LED strip, 5 m on reel
15 cm connection lead at both ends