LED In-Ground Light 36W 4000K Neutral White IP67

LED Damp-Proof Lights for Cellars, Garages and Workshops

LED damp-proof lights are built for rooms where dust, moisture or splash water occur. Their sealed housing with gasket achieves IP65 protection and withstands cleaning with a water jet. Typical locations are cellars, garages, underground car parks, workshops, warehouses and agricultural buildings.

Compared with old fluorescent battens, the LED models save considerable energy and need no tube changes. Length and luminous flux are the main selection criteria: smaller models suffice for cellars, while longer high-output versions make sense in halls. Many luminaires can be linked into continuous light bands.

LED Floodlights for Yards, Facades and Sports Grounds

LED floodlights bring light to large outdoor areas – from the yard and facade to the sports ground. Our range extends from compact 10-watt fittings for the front door to powerful 1.500-watt models for storage yards and sports facilities. All floodlights are weatherproof to IP65 or IP66 and withstand rain, snow and frost.

Some models are available with an infrared motion sensor so the light switches on only when needed, saving energy. Besides wattage, the beam angle matters when choosing: narrow angles reach far, wide angles cover large areas at short distances. We are happy to help determine the right output for your area.

LED Garden Lighting for Outdoor Areas

LED garden lighting stages paths, plants and water features after dark. This category includes inground spotlights for setting into terraces, driveways or lawns as well as underwater lights for ponds, pools and fountains. All fittings are made of stainless steel and protected to IP67 or IP68 depending on the location.

Most models run on 24 volt low-voltage technology, which makes operation outdoors and near water safe. As a planning rule: a few deliberately placed points of light usually work better than uniform continuous lighting. Matching drivers and cable connectors are available in our accessories category.

LED High Bay Lighting for Industry and Commerce

LED high bay lighting has to light large rooms with high ceilings reliably while operating economically. This category includes UFO high bay lights, linear high bay luminaires and canopy fittings for different ceiling heights and uses. Ceiling height, floor area and the type of work are decisive: in warehouses even base brightness matters most, at assembly workstations a low glare rating too.

The beam angle must match the height – narrower for high ceilings, wider for low ones. Compared with old mercury vapour or fluorescent installations, LED high bays often save more than half the energy costs. We are happy to support the design of your hall with a recommendation on quantity and layout.

LED Panels for Office, Practice and Retail

LED panels create a large, evenly lit surface instead of individual bright points. This makes them the standard solution for offices, medical practices, schools and meeting rooms where calm, low-glare light is wanted. We stock backlit panels, in which the LEDs sit behind the diffuser, and edgelit panels with side-fed light and an especially slim design.

The common sizes 60x60, 62x62, 120x30 and 120x60 centimetres are available to suit standard ceiling grids. For ceilings without a grid we offer surface mounting frames that allow direct installation. Watch the UGR value where screen work takes place – the lower, the more comfortable.

LED Track System for Retail and Commerce

An LED track system is the most flexible way to light sales areas. The luminaires are fitted onto the 3-phase busbar via an adapter and can be moved, added to or replaced at any time – with no electrical work at the ceiling. Using the three phases L1, L2 and L3 you switch several lighting groups separately, for example general light and shop window.

This category contains spotlights, linear luminaires, slim panels, food lighting and emergency fittings for the same track. Our adapters fit the common European systems such as Stucchi, Global, Staff, Unipro, Eutrac and Ivela as well as the EU universal standard. If your store layout changes, simply move the luminaires.

LED Street Lighting for Paths, Squares and Residential Areas

LED street lighting replaces old sodium and mercury vapour fittings while considerably reducing energy consumption. This category includes street lights for carriageways, post top luminaires for parks and residential areas, and lanterns in a classic style. All luminaires are protected to IP66 against dust and water jets and built for year-round outdoor use.

Many models allow power and colour temperature to be set by switch, so one fitting serves different situations. In residential areas warm light at 3000 K or below makes sense, as it disturbs residents and insects less. The adapters usually fit poles with 60 and 76 millimetre diameters.

LED Strips for Furniture, Display Cases and Light Lines

LED strips are flexible light bands that can be stuck to almost any surface. Use them to light display cases, shelves, furniture fronts, alcoves and ceiling edges – anywhere a normal luminaire would be too large. We stock two technologies: classic SMD strips with individual visible light points and COB strips that create a continuous, dot-free line of light.

For voltage you can choose between 24 volt low voltage, which needs a driver, and 230 volt strips run directly from the mains. Watch the power per metre: it determines both brightness and the size of driver required. Matching drivers, profiles and connectors are in our accessories category.

LED Accessories for Installation and Operation

A finished lighting project involves more than the luminaire itself. This category contains drivers for LED strips and fittings, motion sensors for retrofitting, brackets and pole adapters as well as cable and plug connectors. Drivers in particular deserve a careful look: the output must match the connected load and should offer around 20 percent headroom so the unit does not permanently run at its limit.

Motion sensors reduce energy costs where light is only needed occasionally – in corridors, stairwells and outdoor areas. Brackets and adapters ensure floodlights and street luminaires sit securely in the intended place. If you are unsure which accessory suits your fitting, just ask us.

LED ground recessed spotlight 36W IP67 24V 304 stainless steel 4000K neutral white

Description

⚡ LED In-Ground Light · 36 W · 4000 K Neutral White · IP67 · 24 V

LED In-Ground Light 36 W 4000 K Neutral White – 2,880 lm · 45° · IP67 · 304 stainless steel

Neutral white light (4000 K) emphasises architecture, stone and modern materials in a clear, factual way. With 36 W and 2,880 lm, the in-ground light is ideal for uplighting tall facades, large trees and plazas. Made of 304 stainless steel, dust- and waterproof to IP67 and safely run on 24 V extra-low voltage.

36 W

POWER

2,880

LUMEN

IP67

PROTECTION

4000 K

LIGHT COLOUR

Stainless-steel in-ground light for outdoors

The powerful light is built from stainless 304 steel with a generous aluminium heat sink and reliably dissipates the higher heat load. Potted electronics and IP67 ensure lasting dust- and waterproofing, and the walk-over flange bears even high loads. The 24 V operation is safe and delivers a focused 45° beam.

Your Benefits at a Glance

Powerful accents 2,880 lm in neutral white (4000 K) from 36 W.	Walk-over & load-bearing Sturdy 304 stainless-steel body with a large heat sink, bears high loads.
IP67 weatherproof Permanently dust- and waterproof – made for demanding outdoor use.	Safe 24 V technology Extra-low voltage (Class III) – safe even on large installations.
Neutral White light 4000 K – driveways, plazas & crisp architectural accents.	Durable & economical Efficient cooling and 30,000 h for continuous operation.

This Light Colour

Fixed light colour of this variant – also available in 3000 K and 4000 K.

4000 K Neutral White – driveways, plazas & crisp architectural accents

Specifications

Property	Value
Power	36 W
Input voltage	AC/DC 24 V
Luminous flux	2,880 lm
Luminous efficacy	80 lm/W
Energy efficiency class	G (EU 2019/2015)
Light colour	4000 K (neutral white)
Colour rendering (CRI)	≥ 80 (Ra)
Beam angle	45°
LED type	SMD 2835 (36 pcs)
Power factor	≥ 0.5
Protection rating	IP67
Protection class	III (SELV)
Housing	304 stainless steel, aluminium heat sink, PC cover
Outer diameter (flange)	Ø 250 mm
Light aperture (Ø)	Ø 190 mm
Cut-out (hole)	Ø 240 mm
Recessed depth (height)	90 mm
Weight	2.42 kg
Operating temperature	−20 °C to +50 °C
Lifespan	30,000 h
Certification	CE, RoHS

Installation & Wiring

The in-ground light is set into a Ø 240 mm hole in the ground; the stainless-steel flange (Ø 250 mm) sits flush with the surface. Important: the light runs on 24 V safety extra-low voltage (AC/DC) and requires a suitable 24 V power supply or transformer (not included). Never connect it directly to 230 V – this will destroy it. Wiring: V+ = brown, V− = blue; make all connections watertight. Installation and wiring only by a qualified electrician.

Applications

Neutral white light (4000 K) emphasises architecture, stone and modern materials in a clear, factual way. The 36 W in-ground light is therefore ideal for uplighting tall facades, large trees and plazas, and it installs flush in the ground so the look stays tidy by day. The walk-over 304 stainless-steel flange withstands weather and load, IP67 protects against dust and moisture, and it runs on safe 24 V extra-low voltage. This creates a clear, modern lighting look – durable thanks to 304 stainless steel, IP67 and a 30,000-hour lifespan.

Scope of delivery: 1 × LED in-ground light (36 W). Note: a separate 24 V power supply or transformer is required for operation (not included).