LED VU1 linear light 30° adjustable 1152mm white 160lm CRI>90

LED Damp-Proof Lights for Cellars, Garages and Workshops

LED damp-proof lights are built for rooms where dust, moisture or splash water occur. Their sealed housing with gasket achieves IP65 protection and withstands cleaning with a water jet. Typical locations are cellars, garages, underground car parks, workshops, warehouses and agricultural buildings.

Compared with old fluorescent battens, the LED models save considerable energy and need no tube changes. Length and luminous flux are the main selection criteria: smaller models suffice for cellars, while longer high-output versions make sense in halls. Many luminaires can be linked into continuous light bands.

LED Floodlights for Yards, Facades and Sports Grounds

LED floodlights bring light to large outdoor areas – from the yard and facade to the sports ground. Our range extends from compact 10-watt fittings for the front door to powerful 1.500-watt models for storage yards and sports facilities. All floodlights are weatherproof to IP65 or IP66 and withstand rain, snow and frost.

Some models are available with an infrared motion sensor so the light switches on only when needed, saving energy. Besides wattage, the beam angle matters when choosing: narrow angles reach far, wide angles cover large areas at short distances. We are happy to help determine the right output for your area.

LED Garden Lighting for Outdoor Areas

LED garden lighting stages paths, plants and water features after dark. This category includes inground spotlights for setting into terraces, driveways or lawns as well as underwater lights for ponds, pools and fountains. All fittings are made of stainless steel and protected to IP67 or IP68 depending on the location.

Most models run on 24 volt low-voltage technology, which makes operation outdoors and near water safe. As a planning rule: a few deliberately placed points of light usually work better than uniform continuous lighting. Matching drivers and cable connectors are available in our accessories category.

LED High Bay Lighting for Industry and Commerce

LED high bay lighting has to light large rooms with high ceilings reliably while operating economically. This category includes UFO high bay lights, linear high bay luminaires and canopy fittings for different ceiling heights and uses. Ceiling height, floor area and the type of work are decisive: in warehouses even base brightness matters most, at assembly workstations a low glare rating too.

The beam angle must match the height – narrower for high ceilings, wider for low ones. Compared with old mercury vapour or fluorescent installations, LED high bays often save more than half the energy costs. We are happy to support the design of your hall with a recommendation on quantity and layout.

LED Panels for Office, Practice and Retail

LED panels create a large, evenly lit surface instead of individual bright points. This makes them the standard solution for offices, medical practices, schools and meeting rooms where calm, low-glare light is wanted. We stock backlit panels, in which the LEDs sit behind the diffuser, and edgelit panels with side-fed light and an especially slim design.

The common sizes 60x60, 62x62, 120x30 and 120x60 centimetres are available to suit standard ceiling grids. For ceilings without a grid we offer surface mounting frames that allow direct installation. Watch the UGR value where screen work takes place – the lower, the more comfortable.

LED Track System for Retail and Commerce

An LED track system is the most flexible way to light sales areas. The luminaires are fitted onto the 3-phase busbar via an adapter and can be moved, added to or replaced at any time – with no electrical work at the ceiling. Using the three phases L1, L2 and L3 you switch several lighting groups separately, for example general light and shop window.

This category contains spotlights, linear luminaires, slim panels, food lighting and emergency fittings for the same track. Our adapters fit the common European systems such as Stucchi, Global, Staff, Unipro, Eutrac and Ivela as well as the EU universal standard. If your store layout changes, simply move the luminaires.

LED Street Lighting for Paths, Squares and Residential Areas

LED street lighting replaces old sodium and mercury vapour fittings while considerably reducing energy consumption. This category includes street lights for carriageways, post top luminaires for parks and residential areas, and lanterns in a classic style. All luminaires are protected to IP66 against dust and water jets and built for year-round outdoor use.

Many models allow power and colour temperature to be set by switch, so one fitting serves different situations. In residential areas warm light at 3000 K or below makes sense, as it disturbs residents and insects less. The adapters usually fit poles with 60 and 76 millimetre diameters.

LED Strips for Furniture, Display Cases and Light Lines

LED strips are flexible light bands that can be stuck to almost any surface. Use them to light display cases, shelves, furniture fronts, alcoves and ceiling edges – anywhere a normal luminaire would be too large. We stock two technologies: classic SMD strips with individual visible light points and COB strips that create a continuous, dot-free line of light.

For voltage you can choose between 24 volt low voltage, which needs a driver, and 230 volt strips run directly from the mains. Watch the power per metre: it determines both brightness and the size of driver required. Matching drivers, profiles and connectors are in our accessories category.

LED Accessories for Installation and Operation

A finished lighting project involves more than the luminaire itself. This category contains drivers for LED strips and fittings, motion sensors for retrofitting, brackets and pole adapters as well as cable and plug connectors. Drivers in particular deserve a careful look: the output must match the connected load and should offer around 20 percent headroom so the unit does not permanently run at its limit.

Motion sensors reduce energy costs where light is only needed occasionally – in corridors, stairwells and outdoor areas. Brackets and adapters ensure floodlights and street luminaires sit securely in the intended place. If you are unsure which accessory suits your fitting, just ask us.

LED VU1 linear light 30° adjustable 1152mm white 160lm CRI>90 4000K

Item number: VU1C911WV-2

Category: VU1 LED Linear Luminaire

Lightcolor:: 3000K4000K5000K6000K

105,90 €

including 19% VAT., no shipping costs

From	Price per unit
6	99,90 €
12	94,90 €

Available

Shipping time: 15 - 16 workdays

Description

LED VU1 Linear Luminaire – Slim Track Spotlight, Individually Tiltable

1152 mm · white · 4000 K neutral white · CRI > 90 · 120°

1152 mmwhiteCRI > 904000 K120°0–30° tiltable160 lm/WL80 100,000 h

With the LED VU1 linear luminaire you get a versatile track spotlight in a slim design. The standard 120° beam provides broad, even base brightness; in addition, each luminaire folds down and swivels individually from 0 to 30° sideways. You can adjust the light direction at any time without moving the luminaire along the track. For controllable installations the luminaire is also available in a DALI-2 version on request: it can then be dimmed steplessly and integrated into a central lighting control system.

Key benefits at a glance

120° beam angle Wide, soft light for evenly illuminated surfaces.	Individually tiltable Folds down and turns 0–30° to the left or right.
Switchable power 48 W / 40 W / 34 W / 27 W – selectable at the switch.	High efficiency 160 lm/W – up to 7,680 lm at 48 W.
Flicker-free PstLM < 1 and SVM < 0.1 – pleasant for eyes and cameras.	Long service life L80 at 100,000 h thanks to Sanan LED chips.

Features in detail

120° standard optic, further beam angles optionally available on request
Fold-down design, individually tiltable 0–30°
Colour rendering CRI > 90 for natural colours
Switchable power in four steps without tools
Optionally available with DALI-2 dimming on request
For 3-phase track – compatible with common track systems
Slim aluminium housing in white, PMMA lens, IK04

Individually tiltable: light exactly where you need it

Individually tiltable means each luminaire can be folded down out of the track and then turned steplessly between 0° and 30° to the left or right. So you aim the light exactly where it is needed – at a shelf wall, a display or a workstation. This is especially handy when the interior changes: instead of rebuilding, you simply re-aim the luminaires.

Beam angles: which one suits your application?

Ex works the luminaire comes with a 120° optic – the classic angle for area lighting. For special requirements further beam angles are available on request. Here is what the individual versions do:

120° (standard) – very wide angle for even base light. First choice for normal ceiling heights up to about 4 m, for aisles, offices, sales rooms and workshops.
90° – slightly more focused than 120°. At the same height it puts more light on the floor and reduces stray light on the walls – good for aisles and shelf rows.
60° – medium angle for higher ceilings (approx. 4–6 m) or when a certain zone should be noticeably brighter than the rest of the room.
30° – narrow spot angle. Creates strong accents on individual products, displays or artworks and suits high ceilings because the light arrives concentrated below.
25° double (DS25°) – two narrow beams from one luminaire. Ideal when two opposite shelf sides of an aisle are to be lit at the same time.
25° asymmetric (L/R) – throws the light offset to the left or right. Perfect for wall shelves, wall pictures or window walls when the luminaire cannot hang directly in front.
Opal cover 120° – a milky cover instead of a lens. The light is diffused softly and the luminous surface looks uniform – particularly low-glare for offices and anywhere soft light is desired.

As a rule of thumb: the higher the ceiling and the more targeted the light should be, the narrower the angle. For normal room heights and even brightness the standard 120° optic is the right choice.

Not sure which beam angle suits your room? Simply get in touch – we are happy to advise you and will find the right optic for your ceiling height and application together with you. The lenses for the different beam angles can be selected at no extra charge after consultation with us.

CRI > 90: colours like daylight

For the highest demands on colour fidelity: CRI > 90 also reveals subtle nuances that simpler light sources swallow. Clothing does not look faded, wood and leather keep their warm tone, food looks fresh. That makes this version ideal for shops, showrooms and display areas.

Long service life – L80 at 100,000 hours

The figure L80 at 100,000 hours describes how slowly the LEDs dim over time. Even after 100,000 operating hours they still emit at least 80 % of their original brightness. There is no sudden failure, only a very slow, barely visible decline – easy to plan for and low on maintenance.

High-quality LED chips by Sanan

A word on the LED manufacturer: Sanan Optoelectronics from Xiamen is not a no-name supplier but the largest producer of LED chips in China and one of the leading ones worldwide. Since its foundation in 2000 the listed company has grown into a vertically integrated group that makes everything itself, from wafer to finished chip – which secures consistent quality across large volumes. This luminaire benefits directly: high efficiency, very tight colour tolerances (SDCM < 5), stable colour rendering and a long service life of L80 at 100,000 hours. Cheap LED chips save money at purchase – good ones save it over the entire service life.

Mounting & track compatibility

Mounting is simple: the luminaire clicks onto a 3-phase busbar via its adapter – place, turn, done. Because the track carries three separate phases, you can switch different groups of luminaires independently. The adapter is compatible with the widespread systems Stucchi, Global, Staff, Unipro, Eutrac and Ivela as well as the EU universal standard; the design is Safety Class I.

Colour temperature 4000 K – neutral white

Neutral white light is businesslike and friendly at once – the all-rounder for sales rooms, boutiques, offices and exhibitions.

Why CRI > 90 delivers slightly fewer lumens

Fewer lumens at CRI > 90 – why? Higher colour rendering comes from a broader spectrum with a stronger red share. The eye perceives red light more weakly than green or yellow, and the necessary phosphor conversion causes extra losses. Together these slightly reduce measured luminous flux and efficacy (lm/W). The gain: colours, fabrics and materials look exactly as they really are.

Power steps & luminous flux

Power step	Power	Luminous flux
Step 1 (maximum)	48 W	7,680 lm
Step 2	40 W	6,400 lm
Step 3	34 W	5,440 lm
Step 4 (minimum)	27 W	4,320 lm

Power is selected directly at the luminaire via switch – so you match brightness to the room without additional devices and save energy permanently.

Technical data

Length	1152 mm
Power (switchable)	48 W / 40 W / 34 W / 27 W (by switch)
Luminous flux	7,680 lm / 6,400 lm / 5,440 lm / 4,320 lm
Efficacy	160 lm/W
Colour temperature	4000 K (neutral white)
Colour rendering	CRI > 90
Beam angle	120° (standard); optionally 90°, 60°, 30°, 25° double, 25° asymmetric L/R or opal cover 120° on request
Tilt range	fold-down, individually 0° to 30° left or right
Mounting	3-phase track (via adapter), phase selection L1/L2/L3
Track compatibility	Stucchi, Global, Staff, Unipro, Eutrac, Ivela, EU universal standard
Voltage	AC/DC 220–240 V, 50/60 Hz
Dimmable	No, optionally DALI-2 dimmable on request
Power factor	> 0.98
Flicker	PstLM < 1, SVM < 0.1 (flicker-free)
Colour consistency	SDCM < 5
LED chip	high-quality brand LEDs by Sanan
Service life	L80 at 100,000 h
Switching cycles	> 500,000
Protection rating	IP20
Impact resistance	IK04
Protection class	I (with protective earth)
Material	aluminium + PMMA lens (opal cover: PC)
Housing colour	White (RAL 9016)
Height	17 mm (lens) / 29.5 mm (opal cover), width 63.5 mm
Weight	1.10 kg
Ambient temperature	−20 °C to +40 °C
Storage temperature	−25 °C to +65 °C
Glow wire test	650 °C
Energy efficiency class	C (EU scale A–G, EU 2019/2015)

Applications

Typical locations are shops, boutiques, supermarkets, showrooms, galleries, offices, conference rooms, corridors and reception areas as well as workshops and exhibition halls. Because the luminaire simply clicks onto the track, the lighting can change along with the room – new shelves, new ranges or a new layout mean no electrical rework, just repositioning and re-aiming the luminaires.

Scope of delivery

1× LED VU1 linear luminaire with 3-phase adapter
Installation instructions

Trademark notice: Stucchi, Global, Staff, Unipro, Eutrac and Ivela are registered trademarks of their respective owners. They are named solely to describe the compatibility of this luminaire with the corresponding 3-phase track systems. There is no business relationship with the companies mentioned; this luminaire is not original accessory equipment of these manufacturers.