Description
NEO CDA – LED Office Floor Lamp 80 W, Direct/Indirect, UGR < 13
11,200 lm · 4000 K · Ra > 80 · touch dimming · motion and daylight sensor
This LED floor luminaire lights the workplace from two directions: a large share of the light goes upwards to the ceiling and returns from there soft and diffused, a smaller share falls directly onto the desk. This combination provides even brightness without harsh shadows and without glare on the screen. It simply stands beside the desk – with no work on the ceiling. Visually it blends in discreetly: the slim lamp head of just 50 mm width and the clean, straight lines suit modern offices as well as the home office.
Key benefits at a glance
Glare-free to standard UGR < 13 – well below the limit for screen work. | Direct and indirect 60 W via the ceiling, 20 W straight onto the desk. |
No installation Place it, plug it in – no work on the ceiling. | Sensors included Motion and daylight sensors reduce consumption. |
High efficiency 140 lm/W – 11,200 lm from 80 W. | Long service life L80(B10) at 50,000 h, no lamp changes. |
Features in detail
- Direct/indirect luminaire with 60 W upward and 20 W downward
- Glare limitation UGR < 13 through micro-reflector optics
- Colour temperature 4000 K
- Colour rendering Ra > 80
- Touch dimming, direct and indirect light adjustable asynchronously
- Motion sensor and daylight sensor as standard
- BOKE driver, SMD 2835 LEDs
- Housing available in silver, black or white
Direct and indirect light: why the split?
Why direct and indirect at all? Purely direct light from above creates harsh shadows and easily reflects in the screen. Purely indirect light looks soft but often puts too little brightness on the desk. This luminaire therefore splits its output: 60 watts shine upwards to the ceiling, 20 watts directly downwards. The ceiling acts as a large reflector that scatters the light and creates base brightness in the room. The direct share ensures the necessary illuminance arrives on the working surface.
UGR < 13 – what it means for screen work
The UGR value describes how strongly a luminaire glares – the lower, the more comfortable. For screen workplaces, workplace regulations usually require a value below 19. This luminaire sits considerably lower at UGR below 13. That is achieved with micro-reflector optics that direct light downwards and limit sideways emission. Looking towards the luminaire while seated, you do not look into bright points of light.
Touch control: dim direct and indirect light asynchronously
The luminaire is operated via touch buttons on the housing. The special feature is asynchronous dimming: direct and indirect light each have their own button and can be switched and dimmed completely independently of each other. You can raise the indirect share to brighten the room while reducing the direct light on the desk – or the other way round. A short tap switches, holding dims steplessly.
Motion sensor and daylight sensor
Two sensors are built in. The motion sensor detects whether someone is present: if no movement is registered for 20 minutes, the luminaire dims to 30 percent; after a further 10 minutes it switches off. When someone returns, it comes on again immediately. The daylight sensor additionally measures incoming daylight and compensates: when the sun shines into the office it dims, when it clouds over it brightens again. Together these noticeably reduce consumption without anyone having to think about a switch.
Service life and colour consistency
Service life is stated as L80(B10) at 50,000 hours. It reads awkwardly but simply means: after 50,000 operating hours at most 10 percent of the luminaires emit less than 80 percent of their original brightness. In typical office use of around 2,500 hours a year that corresponds to roughly 20 years. Lamp replacement is eliminated entirely.
Placed instead of installed
The big advantage of a floor luminaire lies in setup: there is nothing to install. The base measuring 480 × 300 millimetres stands securely beside the desk, the pole carries the lamp head at a height of 1,960 millimetres. You plug the luminaire into an ordinary socket and can move it elsewhere at any time. In rented premises, with changing team sizes or in offices with concrete ceilings this is often the only practical solution – and in every case the quickest.
Housing colour: silver, black or white
The luminaire is available in three housing colours: silver, black and white. Silver looks neutral and suits metal frames and classic office equipment, black sets a modern accent and emphasises the straight lines, white blends discreetly into bright rooms. Technically all three versions are identical – simply choose the colour that suits your interior.
Technical data
| Model | NEO CDA |
| Type | floor luminaire with direct and indirect light |
| Power | 80 W (60 W upward / 20 W downward) |
| Luminous flux | 11,200 lm |
| Efficacy | 140 lm/W |
| Colour temperature | 4000 K |
| Colour rendering | Ra > 80 |
| Glare rating | UGR < 13 |
| Colour consistency | SDCM 3 |
| Beam angle | 140° upward / 80° downward |
| LED | SMD 2835 |
| Driver | BOKE |
| Voltage | AC 200–240 V |
| Power factor | ≥ 0.9 |
| Dimming | touch dimming, asynchronous for direct and indirect light |
| Sensors | motion sensor and daylight sensor |
| Service life | L80(B10) 50,000 h |
| Housing colour | silver, black or white |
| Dimensions | lamp head 1,205 × 50 × 40 mm · pole 1,960 mm · base 480 × 300 mm |
| Weight | approx. 10 kg |
| Energy efficiency class | D (EU scale A–G, EU 2019/2015) |
Applications
The luminaire is used in private offices, open-plan offices, coworking spaces, meeting rooms and home offices. Wherever people work at screens and the existing ceiling lighting is insufficient or glares too much, it noticeably improves the situation – with no electrical work. It is also a sensible addition to existing lighting at individual, particularly demanding workplaces.
Scope of delivery
- 1× LED floor luminaire with lamp head, pole and base
- Connection cable with plug
- Installation and operating instructions