LED VU2 Linear Luminaire 600mm white CRI>80 6000K

LED Damp-Proof Lights for Cellars, Garages and Workshops

LED damp-proof lights are built for rooms where dust, moisture or splash water occur. Their sealed housing with gasket achieves IP65 protection and withstands cleaning with a water jet. Typical locations are cellars, garages, underground car parks, workshops, warehouses and agricultural buildings.

Compared with old fluorescent battens, the LED models save considerable energy and need no tube changes. Length and luminous flux are the main selection criteria: smaller models suffice for cellars, while longer high-output versions make sense in halls. Many luminaires can be linked into continuous light bands.

LED Floodlights for Yards, Facades and Sports Grounds

LED floodlights bring light to large outdoor areas – from the yard and facade to the sports ground. Our range extends from compact 10-watt fittings for the front door to powerful 1.500-watt models for storage yards and sports facilities. All floodlights are weatherproof to IP65 or IP66 and withstand rain, snow and frost.

Some models are available with an infrared motion sensor so the light switches on only when needed, saving energy. Besides wattage, the beam angle matters when choosing: narrow angles reach far, wide angles cover large areas at short distances. We are happy to help determine the right output for your area.

LED Garden Lighting for Outdoor Areas

LED garden lighting stages paths, plants and water features after dark. This category includes inground spotlights for setting into terraces, driveways or lawns as well as underwater lights for ponds, pools and fountains. All fittings are made of stainless steel and protected to IP67 or IP68 depending on the location.

Most models run on 24 volt low-voltage technology, which makes operation outdoors and near water safe. As a planning rule: a few deliberately placed points of light usually work better than uniform continuous lighting. Matching drivers and cable connectors are available in our accessories category.

LED High Bay Lighting for Industry and Commerce

LED high bay lighting has to light large rooms with high ceilings reliably while operating economically. This category includes UFO high bay lights, linear high bay luminaires and canopy fittings for different ceiling heights and uses. Ceiling height, floor area and the type of work are decisive: in warehouses even base brightness matters most, at assembly workstations a low glare rating too.

The beam angle must match the height – narrower for high ceilings, wider for low ones. Compared with old mercury vapour or fluorescent installations, LED high bays often save more than half the energy costs. We are happy to support the design of your hall with a recommendation on quantity and layout.

LED Panels for Office, Practice and Retail

LED panels create a large, evenly lit surface instead of individual bright points. This makes them the standard solution for offices, medical practices, schools and meeting rooms where calm, low-glare light is wanted. We stock backlit panels, in which the LEDs sit behind the diffuser, and edgelit panels with side-fed light and an especially slim design.

The common sizes 60x60, 62x62, 120x30 and 120x60 centimetres are available to suit standard ceiling grids. For ceilings without a grid we offer surface mounting frames that allow direct installation. Watch the UGR value where screen work takes place – the lower, the more comfortable.

LED Track System for Retail and Commerce

An LED track system is the most flexible way to light sales areas. The luminaires are fitted onto the 3-phase busbar via an adapter and can be moved, added to or replaced at any time – with no electrical work at the ceiling. Using the three phases L1, L2 and L3 you switch several lighting groups separately, for example general light and shop window.

This category contains spotlights, linear luminaires, slim panels, food lighting and emergency fittings for the same track. Our adapters fit the common European systems such as Stucchi, Global, Staff, Unipro, Eutrac and Ivela as well as the EU universal standard. If your store layout changes, simply move the luminaires.

LED Street Lighting for Paths, Squares and Residential Areas

LED street lighting replaces old sodium and mercury vapour fittings while considerably reducing energy consumption. This category includes street lights for carriageways, post top luminaires for parks and residential areas, and lanterns in a classic style. All luminaires are protected to IP66 against dust and water jets and built for year-round outdoor use.

Many models allow power and colour temperature to be set by switch, so one fitting serves different situations. In residential areas warm light at 3000 K or below makes sense, as it disturbs residents and insects less. The adapters usually fit poles with 60 and 76 millimetre diameters.

LED Strips for Furniture, Display Cases and Light Lines

LED strips are flexible light bands that can be stuck to almost any surface. Use them to light display cases, shelves, furniture fronts, alcoves and ceiling edges – anywhere a normal luminaire would be too large. We stock two technologies: classic SMD strips with individual visible light points and COB strips that create a continuous, dot-free line of light.

For voltage you can choose between 24 volt low voltage, which needs a driver, and 230 volt strips run directly from the mains. Watch the power per metre: it determines both brightness and the size of driver required. Matching drivers, profiles and connectors are in our accessories category.

LED Accessories for Installation and Operation

A finished lighting project involves more than the luminaire itself. This category contains drivers for LED strips and fittings, motion sensors for retrofitting, brackets and pole adapters as well as cable and plug connectors. Drivers in particular deserve a careful look: the output must match the connected load and should offer around 20 percent headroom so the unit does not permanently run at its limit.

Motion sensors reduce energy costs where light is only needed occasionally – in corridors, stairwells and outdoor areas. Brackets and adapters ensure floodlights and street luminaires sit securely in the intended place. If you are unsure which accessory suits your fitting, just ask us.

LED VU2 linear light 30°x90°V-tiltable 600mm white 165lm CRI>80 6000K

Item number: VU2C86WV-4

Category: VU2 LED linear light

Lightcolor:: 3000K4000K5000K6000K

94,90 €

including 19% VAT., plus shipping

From	Price per unit
6	89,90 €
12	84,90 €

Available

Shipping time: 15 - 16 workdays

Description

LED VU2 Linear Luminaire – Track Spotlight with Two Tiltable Wings

600 mm · white · 6000 K cool white · CRI > 80 · 30° × 90°

600 mmwhiteCRI > 806000 K30° × 90°2 wings 0–30°165 lm/WL80 100,000 h

With the LED VU2 linear luminaire you get a track spotlight that adapts to the room instead of the other way round. The two light wings move individually and can be aimed together or in opposite directions. One row of luminaires can light a wide aisle, two shelf fronts or a single wall. For controllable installations the luminaire is also available as a DALI-2 version on request. In this version it can be dimmed steplessly and integrated into a central lighting control system.

Key benefits at a glance

Two tiltable wings Individually tiltable 0° to 30° – two shelf sides with one luminaire.	30° × 90° optic Wide lengthwise, narrow across: light on the aisle, little spill.
Switchable power 48 W / 40 W / 34 W / 27 W selectable at the switch.	High efficiency 165 lm/W – up to 7,920 lm at 48 W.
Flicker-free PstLM < 1 and SVM < 0.1 – comfortable for eyes and cameras.	Long service life L80 at 100,000 h thanks to Sanan LED chips.

Features in detail

Two separately tiltable light wings, each adjustable 0° to 30°
Beam angle 30° × 90°, 30° × 30° optionally available on request
Colour rendering CRI > 80 for natural colours
Switchable power in four steps without tools
Optionally available with DALI-2 dimming on request
For 3-phase track – compatible with common track systems
Aluminium housing in white with PMMA lens, IP20, IK04

Two tiltable wings: one luminaire, many lighting effects

What do two tiltable wings mean in practice? The luminaire has two separate light rows that you can tilt independently by up to 30°. Set both straight down and you get an even band of light. Tilt them outwards and one luminaire lights two opposite shelf fronts. Tilt both to the same side and you concentrate the full light output on one wall or product display.

Beam angles: which one suits your application?

Two optics are available for the VU2. Fitted as standard is 30° × 90°; on request we supply the narrow 30° × 30° version. The difference in practice:

30° × 90° (standard) – a beam that is wide lengthwise and narrow across. Light spreads far along the luminaire while staying focused across it. Ideal for aisles, shelf rows and long sales areas: plenty of light on the goods, little spill into neighbouring zones.
30° × 30° (optional) – a narrow beam focused in both directions – comparable to a spotlight. It brings light down in a concentrated cone and suits high ceilings from about 4–5 m as well as targeted accents on individual products, displays or exhibits.
Tilt 0° to 30° – regardless of the beam angle, each of the two wings can be tilted. This shifts the beam sideways without moving the luminaire itself – onto a shelf front instead of the aisle floor, for example.

As a rule of thumb: the higher the ceiling and the more targeted the light should be, the narrower the angle. For normal room heights and continuous aisles the standard 30° × 90° optic is the right choice.

Not sure which beam angle suits your room? Simply get in touch – we are happy to advise you and will find the right optic for your ceiling height and application together with you. The lenses for the different beam angles can be selected at no extra charge after consultation with us.

CRI > 80: maximum light per euro

CRI > 80 is the proven standard in retail and industry. Colour rendering is good, while efficiency at 165 lm/W is considerably higher than in the CRI 90 version. Anyone running many luminaires noticeably reduces energy costs – with a light quality that is perfectly adequate for most applications.

Long service life – L80 at 100,000 hours

Behind the figure L80 at 100,000 hours lies a simple statement: even after 100,000 operating hours the luminaire still delivers at least 80 % of its initial brightness. LEDs do not fail suddenly like an incandescent bulb; they dim very gradually over a long period. At twelve hours of use per day this value covers more than twenty years.

High-quality LED chips by Sanan

It is worth looking at the LED manufacturer: Sanan Optoelectronics was founded in Xiamen in 2000, is stock-listed and is today the largest producer of LED chips in China as well as one of the top suppliers worldwide. Manufacturing at that scale means strict quality control and very low variation. The VU2 benefits directly: plenty of light per watt, precisely maintained colour temperature and a light output that stays stable over the years.

Mounting & track compatibility

All you need for installation is an existing 3-phase busbar: the VU2 is inserted, turned and sits securely. That makes later changes easy – new shelving or a new layout requires no electrical rework, just repositioning the luminaires. Phase selection L1/L2/L3 separates lighting circuits. Compatible with Stucchi, Global, Staff, Unipro, Eutrac, Ivela and the EU universal standard, Safety Class I.

Colour temperature 6000 K – cool white

Cool white light delivers maximum brightness and contrast – proven in warehouses, production and high spaces.

Power steps & luminous flux

Power step	Power	Luminous flux
Step 1 (maximum)	48 W	7,920 lm
Step 2	40 W	6,600 lm
Step 3	34 W	5,610 lm
Step 4 (minimum)	27 W	4,455 lm

Power is selected directly at the luminaire via switch. This way you match brightness to the room without additional devices and save energy permanently.

Technical data

Length	600 mm
Power (switchable)	48 W / 40 W / 34 W / 27 W (by switch)
Luminous flux	7,920 lm / 6,600 lm / 5,610 lm / 4,455 lm
Efficacy	165 lm/W
Colour temperature	6000 K (cool white)
Colour rendering	CRI > 80
Beam angle	30° × 90° (standard); 30° × 30° optionally available on request
Tilt range	two wings, individually tiltable 0° to 30°
Mounting	3-phase track (via adapter), phase selection L1/L2/L3
Track compatibility	Stucchi, Global, Staff, Unipro, Eutrac, Ivela, EU universal standard
Voltage	AC/DC 220–240 V, 50/60 Hz
Dimmable	No, optionally DALI-2 dimmable on request
Power factor	> 0.98
Flicker	PstLM < 1, SVM < 0.1 (flicker-free)
Colour consistency	SDCM < 5
LED chip	high-quality brand LEDs by Sanan
Service life	L80 at 100,000 h
Switching cycles	> 500,000
Protection rating	IP20
Impact resistance	IK04
Protection class	I (with protective earth)
Material	aluminium + PMMA lens
Housing colour	White (RAL 9016)
Dimensions	600 × 84.6 × 55 mm (L × W × H)
Weight	1.97 kg
Ambient temperature	−20 °C to +40 °C
Storage temperature	−25 °C to +65 °C
Glow wire test	650 °C
Energy efficiency class	C (EU scale A–G, EU 2019/2015)

Applications

Typical locations are shops, supermarkets, specialist stores, boutiques, showrooms, galleries, offices, workshops and exhibition areas. Because the two wings tilt independently, the luminaire adapts to different tasks: straight down for even aisles, spread outwards for shelf fronts left and right, swivelled together for an accented wall. If you change your layout, simply re-aim the light.

Scope of delivery

1× LED VU2 linear luminaire with 3-phase adapter
Installation instructions

Trademark notice: Stucchi, Global, Staff, Unipro, Eutrac and Ivela are registered trademarks of their respective owners. They are named solely to describe the compatibility of this luminaire with the corresponding 3-phase track systems. There is no business relationship with the companies mentioned; this luminaire is not original accessory equipment of these manufacturers.